1. <source id="jp2rc"><xmp id="jp2rc"><video id="jp2rc"></video>
        <u id="jp2rc"><div id="jp2rc"></div></u>
        <b id="jp2rc"></b>

        China mold maker&plastic injection molding company

        Professional & Trustable Plastics Mold Maker

        China injection molding making company

        injection mold heater and cooling system

        Home > Article > Plastic Injection Molding >


        China Plastic Injection Molding companies -heating and cooling system

        Rapid heat temperature actually is an old china plastic injection molding companies method that is often
        used to eliminate the weld line, the front cover products such as medicine accessory. Here is an example
        of the most frequently used method, but its use is now developed further, as demand  for products with low
        cycle time and quality of surface nice sharp increase lately, covering progress being made is that the control
        the system is used, so the heat on the heating rod is held constant, the only heating occurs during the process of
        filling, so filling process stops, and the cooling process is done, no heating rod heating process.

        Advantage of china plastic injection molding system

        Trim cycle times up to 20 % in the plastic injection molding process. A new unit combines rapid heating and
        cooling and mold-temperature control in one unit as a means to trim cycle times by up to 20% and reduce
        energy cost.

        It is the result of a collaboration between china plastic injection molding company, a supplier of pulsed
        mold heating/cooling systems, and CN-moulding, a china mold maker of fluid temperature-control units Reduce
        Weld line because during the process of filling, the mold is heated, especially at the regional meeting of the
        plastic, this led to the solidification of the material evenly, so that the weld line can be minimized. injection
        mold is rapidly heated to a high temperature, usually higher than the glass transition temperature of the polymer
        material, before melt-injection and rapidly cooled down to solidify the shaped polymer melt in the mold cavity for
        ejection.Since the elevated mold temperature can eliminate the unwanted premature melt freezing during filling
        stage, the melt flow resistance is greatly reduced and the filling ability of the polymer melt is also significantly
        improved. As a result, plastic parts with excellent surface appearance can be obtained.  Improve Appearance
        of china plastic injection molding companies system, rapid heat cycle method is also shown to improve the
        quality of the surface, this is because of the process of filling with stable temperatures ranging from the gate
        to the end product, or it could be said to be due to differences in temperature in the cavity is not much different.
        Reduce Cost of China plastic injection molding companies system


        I was not sure whether china plastic injection molding companies method can reduce the cost of
        production, when production is carried out is to a large scale, of course, 10-20% reduction in cycle time
        will bring a lot of meaning to the cost of production, but when the scale of SMEs, given the initial price for the
        application of this method expensive.

         

        china plastic injection molding companies method reduce production costs Heating Method
        of china plastic injection molding company various types of heating methods research have been
        carried out



        1. use of the insulation layer, An insulation layer is coated onto the mold base then a heating layer is applied to
        the insulation layer as the cavity surface, for Increasing the mold surface temperature in the filling process, a
        the coating on the cavity surface with TiN and Teflon has reduced the heat transfer from the melt to the mold
        material, which Increased the temperature on the cavity surface.


        2. the use of steam. the difficulty of this method is the first installation costs are expensive, and slow increase in
           temperature,


        3. Infrared radiation on the surface, this method has also been investigated, and are able to reduce cycle
            time by 20%


        4. electric heating rod, this method is the method most commonly used in industry because of the installation,
            maintenance, repairs are relatively easy. but the price per Kw electricity is relatively expensive, because it
            takes a minimum of 300 watts for a heating rod.

         


        Reference video for China Injection Molded Plastics at 

        You many interest these articles and tagged Cooling , Post entrance in Plastic Injection Molding

        Other Item In Category

        Facebook Twitter YouTube LinkedIn

        Contact Us

        Copyright 2013 www.euzjvj.com All Rights Reserved.
        Top↑
        米奇影院